[HAL]stm32F407 DAC+DMA+TIM6查表法产生正弦波

1.STM32CUBEMX配置

时钟： 调试方式： 时钟我配了最大值： 定时器6：这里定时器溢出频率为84M/84/10=100KHZ

DAC: DMA: 生成代码 在main函数之前添加正弦码表：

/* USER CODE BEGIN PM */
const uint16_t Sine12bit[100]={
          
   
0x0800,0x0881,0x0901,0x0980,0x09FD,0x0A79,0x0AF2,0x0B68,0x0BDA,0x0C49,
0x0CB3,0x0D19,0x0D79,0x0DD4,0x0E29,0x0E78,0x0EC0,0x0F02,0x0F3C,0x0F6F,
0x0F9B,0x0FBF,0x0FDB,0x0FEF,0x0FFB,0x0FFF,0x0FFB,0x0FEF,0x0FDB,0x0FBF,
0x0F9B,0x0F6F,0x0F3C,0x0F02,0x0EC0,0x0E78,0x0E29,0x0DD4,0x0D79,0x0D19,
0x0CB3,0x0C49,0x0BDA,0x0B68,0x0AF2,0x0A79,0x09FD,0x0980,0x0901,0x0881,
0x0800,0x077F,0x06FF,0x0680,0x0603,0x0587,0x050E,0x0498,0x0426,0x03B7,
0x034D,0x02E7,0x0287,0x022C,0x01D7,0x0188,0x0140,0x00FE,0x00C4,0x0091,
0x0065,0x0041,0x0025,0x0011,0x0005,0x0001,0x0005,0x0011,0x0025,0x0041,
0x0065,0x0091,0x00C4,0x00FE,0x0140,0x0188,0x01D7,0x022C,0x0287,0x02E7,
0x034D,0x03B7,0x0426,0x0498,0x050E,0x0587,0x0603,0x0680,0x06FF,0x077F,
};
uint16_t DualSine12bit[100];

/* USER CODE END PM */

在main函数中读取码值并做DA输出

int main(void)
{
          
   
  /* USER CODE BEGIN 1 */
	uint32_t Idx;        //定义变量
  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_DAC_Init();
  MX_TIM6_Init();
  /* USER CODE BEGIN 2 */
	 for (Idx = 0; Idx <100; Idx++)  
	{
          
     
		DualSine12bit[Idx] = Sine12bit[Idx]; 
	}
	HAL_TIM_Base_Start(&htim6);
    HAL_DAC_Start_DMA(&hdac,DAC_CHANNEL_1,(uint32_t *)DualSine12bit,100,DAC_ALIGN_12B_R);


  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
          
   
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}